How To Fix HP Printer Alignment Failed Issue?

Trying to align the printheads or cartridges but, unfortunately, get failed to do so? Generally, you encounter the HP Printer Alignment Failed issue at the time of installing new ink cartridges. If this happens, your printer will not receive ink from the cartridges and thus poorly impact the print quality. However, the Printer alignment unsuccessful problem can be rectified with simple and straightforward tricks. Learn in this post why your printer alignment keeps failing and how to fix it instantly. Continue reading with fluency!

Why Is Your HP Printer Continuously Saying Alignment Failed?

Here’s the list of common causes that can prevent your printer from aligning the cartridges properly. Check out them:

1.        Maybe you are attempting to install non-genuine HP ink.

2.        Incorrect installation of ink cartridges will also be a feasible reason for HP Printer Alignment Failed Error.

3.        Physical damage to the printer itself.

4.        Clogged PrintHead.

5.        Insufficient ink levels.

Productive Solutions For HP Printer Alignment Failed Error

We have compiled the proven techniques that will lead to quickly solving the HP Printer Alignment Failed issue. So, without delay, perform the below solutions one after another until your printer alignment gets successfully done. Let’s work your way!

Solution 1: Reset The HP Printer

Resetting the printer will let it recover from the alignment failures. Here’s the step to follow for printer reset:

1.        If your HP Printer product has a rechargeable battery, carefully take it out.

2.        With the printer turned on, disconnect the power cord from the printer.

3.        Unplug the power cord from the power source or wall outlet.

4.        Wait 60 seconds or a couple of minutes.

5.        Reconnect the power cord to a wall outlet and the printer as well.

6.        Turn ON your HP Printer now to complete the reset.

Solution 2: Check Your HP Ink Levels

If the HP Ink is low/empty or incorrectly installed in the printer cartridges, then also the HP Printer Alignment Failed problem occurs. In such a scenario, you need to ensure your printer has sufficient ink levels. Here’s how:

1.        First and foremost, open the ink cartridge access door on your printer product.

2.        Next, wait for the carriage to stop moving.

3.        After that, slightly remove each cartridge.

4.        Eliminate the protective tape if having any on the cartridges.

5.        Examine properly and eradicate any obstructions if surrounded by the printer carriage.

6.        Replace ink cartridges that are low or out of ink. But, make sure you prefer genuine HP Ink during its replacement.

7.        Reinstall the cartridges into their correct slots precisely and then make sure they are firmly seated.

8.        Now, close the ink cartridge access door.

Solution 3: Clean The Ink Cartridges

Accumulation of dust or debris on the ink cartridges can interfere with the alignment. That’s why, it is important to clean the dust particles and contacts on the cartridges using lint-free cloth. Be careful while removing the dust, otherwise, a single mistake can cause printer damage.

Solution 4: Review The Alignment Page

Checking the HP alignment page will help you identify the actual problem. The piece of information that appeared on the printed page will be clearly visible. If the information is faded or the availability of streaks can give a strong indication that the alignment is not correct.

Following are the recommended tips to be used for ensuring the alignment is correct:

1.        Try to load the right type of paper stack in your printer’s input tray.

2.        Ensure that the device’s printhead nozzle isn’t clogged.

3.        The ink levels of your ink cartridge should not be minimal.

4.        The printed alignment page should be of good quality.

Solution 5: Remove Paper Bits From Paper Tray

A small piece of paper may get unknowingly stuck in the HP Printer. Due to the paper jam, you can be noticing a problem with the HP Printer Alignment Failed Error. Immediately take out the torn paper from the tray. Here’s how:

1.        First, open the printer’s cover and inspect the parts inside.

2.        If you detect any jammed paper in the printer tray, cautiously remove it.

3.        If no paper is jammed, then look for debris or smudged one and remove it.

Isn’t It Helpful! Consult HP Printer Support Anytime For Advanced Guide

 

Hope, the aforesaid troubleshooting tips and tricks are effective in quickly resolving HP Printer Alignment Failed. But, if none of these solving methods work, it is a good idea to consult HP Printer Support for further assistance. The executive team will assist you properly so the alignment issues you’re facing will be instantly solved from the root.